BM 5500 DL C

ENGINE

Manufacturer : Deutz
Cooling : Water
RatedPower : 90 kW /121 HP @ 2300 rpm
Cylinder : 4 stroke 3600 cm³
Type : 4 stroke, common rail diesel with turbo and intercooler
Approval : EU Stage IV final ( Stage V ready) – US Tier 4. CRT + SCR, AdBlue

COMPRESSOR

Compressor Capacity : Hydraulic driven, air screw 2400 or 4500 L/min @ 10 bar. Integrated oil system with external oil cooler. Water separator.

FILLING CAPACITIES

Fuel tank capacity : 159 L (78 +81 L)
Hydraulic tank size : 126 L
Bead capacity : 330 L (2x 165 L). Pressurized (max 3 bars)

MATERIAL TANK

Material Tank : 585 L and 440 L

DRIVING PROPERTIES

Drive angle : 8° or 14% at 21 km/h, 17° or 30% at 11km/h
Turning radius : 4.9 m
Steering : Hydraulic dual torque steering

TRANSMISSION

Hydrostatic transmission : For variable speed, forward/backwards
Speed : Low gear 0-12 km/h, high gear 0-24 km/h

ELECTRICAL SYSTEM

Electrical system : 12 V / 150 Amp

CONTROL UNIT

Borum LineMaster : Program up to 99 different line types. Organise lines in up to 30 marking programs. 8" display. Transfer of daily marking reports. Data about road marking jobs can be accessed online (optional).

COLOUR

Colour : Borum Yellow (Other colours available on request)

DIMENSIONS

Length : 5350 mm
Width : 1300 mm
Height : 2250 mm (Without Beacon)
Length : 5904 mm
Width : 1346 mm (dimensions are without equipment)

MATERIAL TANK FOR COLD PAINT, PRESSURIZED

Pressurized black steel tank for solvent - based cold paint.The material tank has a filling system with large filling holes. This makes the filling process very easy to manage. In addition, the large filling holes also make cleaning the tanks easy.Agitator (mixer) Driven by hydraulic motor and with manually operated reversing valve.

STAINLESS TANK (OPTION)

Pressurized material tank and filters in stainless steel for water and ammonium based paints.

THERMOPLASTIC NON-PRESSURIZED TANK:

Non-pressurized thermoplastic tank, indirectly heated via heat transfer oil. The thermal oil and thermoplastic material temperature is thermostatically controlled and regulated automatically according to the settingsBurner systemDiesel burner system for heating of the thermal oil (and thermoplastic). Propane burner is available on demand.Vertical agitator (mixer)With hydraulic transmission. Heated center pipe for efficient uniform temperature control. Perfect melting & homogenization of the thermoplastic. Stable construction with foundation and bearings at the top of the material tank.

Cold paint equipment specifications

Air spray with atomizing air is a method of marking that uses a pressure tank for the material and compressed air to atomize and spray the paint onto the road surface. For all Borum spray machines, the equipment is mounted on a sliding retainer frame as standard that allows you to quickly slide the equipment from one side to another. You can have 1-3 paint guns, depending on the set-up of the machine, and 1-3 bead guns are attached.The ground distance is maintained by a retainer wheel to ensure a constant road marking width. Lifting of retainer is pneumatic and done from the operator's seat. Paint filter with cut-off valve for easy maintenance. The machine can be equipped with two material tanks so that dual-color marking can be carried out simultaneously. Working speed can be up to 15 km/h depending on the conditions, e.g. material, line type, and operator experience.

BM C6 COLD PAINT GUN

High-performance spray gun. with a 6 mm nozzle set for water-based, solvent-based and high solid paints. The BM C 6 gun can work with paint marking pressure up to approx. 8 bar.Air capacity of 300-700 L/min. is needed per gun.Possibility to apply lines in widths from 8 to 20 cm with one gun depending on work conditions, nozzle size, application speed, and layer thickness. Line thickness is typically between 0.25 mm to 0.80 mm.

COLD PAINT FEATURES

Cold paint material is a cost-effective solution for executing flat markings over all types of pavements and for use in repairments. Flat lines are mainly used in well-illuminated areas as urban roads for e.g. where the lines do not need high retroreflectivity levels. Although drying time different between types of paints, it is usually quite long and cones and traffic management might be needed.

3-in-1 solution for thermoplastic markings

The Dot’n line system offers a three-in-one solution for thermoplastic markings. This equipment can apply flat lines, dots and unique combination of lines and dots using only one extruder head.In the drawing you can see examples of different valve set-ups giving different widths. The total line width can be between 30-50 cm depending on the set-up. The line width starts at 5 cm and can be built up to 50 cm with 5 cm standard shutters.

Dot specifications

By using two sets of shutters the base line has time to cure slightly before the Dots are applied. Consequently, the Dots will settle on top of the line with sharp edges, securing the optimum retroreflection.The diameter of dots can be chosen between ø18 and ø 45 mm depending on the chosen drum. The number of dots/meter is 15-35 dots and is controlled by the LineMaster.The shutters have no contact with the high tensile steel drum and therefore wear is minimalized and lifetime is prolonged.Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven.Pneumatically controlled quick cleaning systemfor removal of solids left in the extrusion slot.It can be activated while extrusion is in processand is only slightly detectable on the line in theform of a moderate thickening of the layer.Continuous circulation of the thermoplastic material inside the equipment. This avoids settling and catching of solid parts and prevents unnecessary wear of mechanical parts.The application speed depends on the type of application and goes up to 6 km/h.

AUGER SCREW PUMP WITH CONTINUOUS RECIRCULATION SYSTEM

The transport of material from tank to Dot'n'Line head is done by a hydraulically driven auger screw pump, which is electronically controlled. The screw pump has a permanent thermoplastic re-circulation system, which ensures a constant flow also past the inactive extrusion shutters, keeping solid parts from settling and keeping the equipment ready for working.Build-in pressure regulating system ensures that line width and thickness do not change no matter the number of shutters involved in the current marking assignment.

Advantages of profiled dot markings

Having numerous dots in a line gives the light a lot of possible areas to fall onto and create a retro-reflective effect. This is essential for having clear visibility, especially while driving during night time.The drainage effect of the profiled markings ensures that rain water will easily drain away from the lines, thus maintaining high reflective values in rainy weather. This is possible because of the structure that allows the water to drain. Furthermore, the profiled nature of the road marking produces a noise when driven over that will warn the driver against driving off the road.

CLEANING SYSTEM

10L pressure solvent tank for cleaning of hoses and paint guns.

LineMaster features

The Borum LineMaster control unit is an easy way of setting and controlling your line marking jobs. The LineMaster is attached to the operator's section of the machine and gives you full control of all your line marking tasks, from line application and pre-marking to reporting and invoicing. It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types and different combinations to have them ready for marking, and can instantly adjust them on the go.Furthermore, you are able to view the status of various parts of the machine (e.g. compressor) on the computer screen that will help with correctly maintaining the machine and avoiding break downs.