The Borum Master 3000 series provides you with a variety of high capacity line marking machines designed for medium to large scale jobs such as marking highways, motorways or airport runways.

The material tank capacity can be up to 445L. The possibility for the large material capacity naturally gives fewer stops during the day for refilling.

The BM 3000 has a two-seat slidable drive and operator section for flexible working on the left or right side.

The screed equipment with rib function can apply flat lines, long flex, and rib over the line in fixed prechosen line widths up to 20 cm.

Depending on the equipment and set-up, the extrusion equipment can apply lines of up 5 - 50 cm width, while the rib line equipment comes with fixed line widths up to 20 cm.

Line Types
  • LineType1
  • LineType2
  • LineType3
  • LineType4
  • LineType7
  • LineType8

Line types that can be applied with this equipment

Contact us about this product

ENGINE

  • Manufacturer : Kubota
  • Type : Turbo (Diesel)
  • Cooling : Water
  • Cylinder : 4 stroke 3600 cm3
  • RatedPower : 63 KW
  • Approval : EU Stage IIIA resp. TIER 3

COMPRESSOR

  • Compressor Capacity : Choice of 1-2 compressors can give 1800 - 3600 L/min @ 10 bar. Integrated oil-cooling system. Air-cooler incl. water separator

FILLING CAPACITIES

  • Fuel tank capacity : 180 L (2 x 90 L) - Diesel
  • Hydraulic tank size : 93 L
  • Bead capacity : 330 L (2 x 165 L). Pressurized (max 3 bars)

MATERIAL TANK

  • Material Tank : 445 L

DRIVING PROPERTIES

  • Drive angle : 10.4 degrees / 18% (5000 kg)
  • Turning radius : 4.90 m.
  • Steering : Dual torque steering

TRANSMISSION

  • Hydrostatic transmission : For variable speed
  • Speed : 0-22 km/h

ELECTRICAL SYSTEM

  • Electrical system : 12 V / 130 Amp

CONTROL UNIT

  • Borum LineMaster : Program up to 99 different line types. Organise lines in up to 30 marking programs. 8" display. Transfer of daily marking reports. Data about road marking jobs can be accessed online (optional).

COLOUR

  • Colour : RAL 1007 (Other colours available on request)

DIMENSIONS

  • Length : 5350 mm
  • Width : 1300 mm
  • Height : 2250 mm

THERMOPLASTIC NON-PRESSURIZED TANK:

Non-pressurized thermoplastic tank indirectly heated via heat transfer oil. The thermal oil and thermoplastic material temperature is thermostatically controlled and regulated automatically.

Burner system
Diesel burner system for heating of the thermal oil (and thermoplastic). Propane burner available on demand.

Vertical agitator (mixer)
With hydraulic transmission. Heated center pipe for efficient uniform temperature control. Perfect melting & homogenization of the thermoplastic. Stable construction with foundation and bearings at the top of the material tank.

THERMOPLASTIC SCREED BOX WITH RIB FUNCTION

The screed box can apply flat lines, long flex, and ribs over a line on line in one pass. The Borum thermoplastic screed box is available in the following widths: 10, 12, 15, 20 cm.

With this type of screed application, the box is dragged with constant contact to the surface. The contact points determine the line width. The material pressure is by gravity only and this is how the material is poured in the marking box. The material coming out of the box will fill up any holes, pores, or other types of road imperfections. This means that material consumption will depend on the road surface.

The screed box equipment is mounted directly on the side of the chassis.

The equipment is constructed with one main application box. If you do not need to switch the line widths often, you have the option to only change the application
opening based on your width requirements instead of the whole box! This makes the application equipment more cost-efficient!

The Borum thermoplastic screed box is available in the following widths: 10, 12, 15, 20 cm. Other sizes available upon request.

The thickness for application of flat lines is usually between 2 - 4 mm.

RIB LINE FUNCTION
The screed box is also equipped with a rib function. This allows you to apply ribs over a line in one pass. The total height of line with rib is usually between 8 to 15 mm depending on the material. The lines are recommended to be as thin as possible when combined with ribs (approx. 1,5 - 2 mm).

The usual application speed for applying
ribs over a flat line is 1-3 km/h, while for
screed application of flat lines it is up to 5
km/h.

LASER SENSOR FOR MEASURING AND REFILLING MATERIAL

The equipment is also supplied with a laser that constantly measures the material level in the application box. If the material level becomes lower than 50%, the application box will be automatically refilled.

THERMOPLASTIC MATERIAL ADVANTAGES

Thermoplastic material has a long-life duration with high retro-reflectivity capabilities due to being able to pre-mix glass beads in the material. Thermoplastic markings cure quickly and adhere strongly to the road surface. Generally, thermoplastic is recommended for areas with high traffic density and/or areas with low lighting as e.g. highways.

The rib line equipment is a cost-efficient marking equipment with reduced investments cost for thermoplastic application. This is a good solution if you are only going to work with flat markings and rib line application.

An alternative to the rib line equipment is the Borum thermoplastic extruder with which you can apply various flat and profiled markings. The extruder also uses a different application method by extruding an even layer of material on the road surface. Therefore, if the surface is rough or uneven, the line is the same as it follows the imperfections. In other words, the material consumption will be predictable according to the adjustments and will not be as influenced by the type and condition of the road surface.

EXTRUDER SET-UP

The working principle of the extruder lies in the extrusion of the hot thermoplastic material through the extruder valves onto the road surface. This allows to switch in between line types in seconds with a push of the button. No need for mechanical adjustment.

The thickness of the line is controlled by the slot gap and the speed of the machine, coupled to the thermoplastic feed rate.

Glass beads can be pre-mixed and/or automatically applied with glass bead guns.

You can choose between thermoplastic extruder of 30, 40, or 50 cm in total line width, built-up with 5 cm standard valves (alternative valve dimensions in the range of 4-10 cm for alternative line widths).

EXTRUDER SPECIFICATIONS

Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven. This ensures optimal performance and that the material does not stiffen and set inside the equipment.

The shutters do not touch the high tensile steel drum and therefore, this can lead to an increased lifetime.

Pneumatic lifting cylinder for up/down function, operation controlled from operator’s seat.

Pneumatically controlled quick cleaning function for the removal of solids left in the extrusion slots can be activated while extrusion is in process.

The application speed goes up to 8-10 km/h. Speed-dependent settings possible.

SCREW PUMP WITH CONTINUOUS RECIRCULATION SYSTEM

The transport of material from tank to extruder head is done by a hydraulically driven screw pump, which is electronically controlled. The screw pump has a permanent thermoplastic recirculation system which ensures a constant flow past the in-active extrusion valves, keeping these clean and ready for opening. This avoids settling and catching of solid parts and prevents unnecessary wear of mechanical parts.

Build-in pressure regulating system ensures that line width and thickness does not change no matter the number of the shutters involved in the current marking assignment.

FEATURES - THERMOPLASTIC EXTRUDER:

Thermoplastic is a durable material that cures quickly and adheres strongly to the road surface. It can be used for applications of both flat lines (also known as type 1 lines) or of thick profiled lines and markings (also known as type 2 lines).

This type o material is used on various types of roads, but you will often see it on highways or motorways as it can outstand high traffic density, it has a high visibility at night and during wet conditions and glass beads can be mixed in for further enhancing visibility.

LineMaster features

The Borum LineMaster control unit is an easy way of setting and controlling your line marking jobs. The LineMaster is attached to the operator's section of the machine and gives you full control of all your line marking tasks, from line application and pre-marking to reporting and invoicing.

It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types, colours and combinations to have them ready for marking, and can instantly adjust them on the go.

Furthermore, you are able to view the status of various parts of the machine (e.g. compressor) on the computer screen that will help with correctly maintaining the machine and avoiding break downs.

QUICK CLEANING

Pneumatically controlled quick cleaning system for removal of solids left in the extrusion slot. It can be activated while extrusion is in process and is only slightly detectable on the line in the form of a moderate thickening of layer.

Mounting the RibLine equipment

Ejector filling of bead tank

Pointer turning with steering

With hydraulic lifting system

Fixed pointer

With hydraulic lifting system

Cruise control

Sunshade with 1 rotating light

Bead alarm mounted on bead gun

Remote control for BM LineMaster

Cone holder

Bar with pneumatic lift for mounting warning lights

(Comes without lights)

Air drier for bead tank

BM Online

Pre-marking system with paint gun

Airknife

Pre-marking system with paint can

Hydraulic broom

Quick shift

BORuM ON SOCIAL MEDIA

Follow us on these social platforms