BM 2700 SP DL RL

THERMOPLASTIC SCREED BOX WITH RIB FUNCTION

The screed box can apply flat lines, long flex, and ribs over a line in one pass. With this type of screed application, the box is dragged with constant contact to the surface. The contact points determine the line width. The material pressure is by gravity only and this is how the material is poured in the marking box. The material coming out of the box will fill up any holes, pores, or other types of road imperfections. This means that material consumption will depend on the road surface.The screed box equipment is mounted directly on the side of the material tank.The Borum thermoplastic screed box is available in the following widths: 10, 12, 15, 20, 24, 25, 30 cm. Other sizes are available upon request.The equipment is constructed with one main application box covering a range of line widths, either 0 - 20 cm or 20 - 30cm. If you do not need to switch the line widths often, you have the option to only change the application opening based on your width requirements instead of changing the whole box! This makes the application equipment more cost-efficient!The thickness for the application of flat lines is usually between 2 - 4 mm.The usual application speed for applying ribs over a flat line is 1-3 km/h, while for screed application of flat lines it is up to 5 km/h.RIB LINE FUNCTIONThe screed box is also equipped with a rib function. This allows you to apply ribs over a line in one pass. The total height of line with rib is usually between 8 to 15 mm depending on the material. The base line is recommended to be as thin as possible when combined with ribs (approx. 1,5 - 2 mm).

LASER SENSOR FOR MEASURING AND REFILLING MATERIAL

The equipment is supplied with a laser that constantly measures the material level in the application box. If the material level becomes lower than 50%, the application box will be automatically refilled.

THERMOPLASTIC MATERIAL ADVANTAGES

Thermoplastic material has a long-life duration with high retro-reflectivity capabilities due to being able to pre-mix glass beads in the material. Thermoplastic markings cure quickly and adhere strongly to the road surface. Generally, thermoplastic is recommended for areas with high traffic density and/or areas with low lighting as e.g. highways. The rib line equipment is a good solution if you are only going to work with flat fixed-line width markings and rib line application. An alternative to the rib line equipment is the Borum thermoplastic extruder with which you can apply various flat and profiled markings. The extruder also uses a different application method by extruding an even layer of material on the road surface. Therefore, if the surface is rough or uneven, the line is the same as it follows the imperfections. In other words, the material consumption will be predictable according to the adjustments and will not be as influenced by the type and condition of the road surface.

THERMO SPRAY APPLICATION

Sliding retainer frame, upon which 1-3 spray guns and 1-3 bead guns can be attached. Easy slidable from side to side for an optimal working position. Ground distance is maintained by retainer wheels hereby ensuring a constant road marking width.Lifting of retainer from operators seat is done using a hydraulic cylinder.All material pipes are oil-jacketed and insulated to maintain an ideal material temperature.Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven.Line thickness is typically between 0.75 mm to 1.5 mm.Marking speed up to 15 km/h depending on the work conditions, operator, etc.

GUN FOR SPRAY-PLASTIC APPLICATION

Automatic high-capacity spray plastic gun. Consists of an oil jacketed gun body and a pneumatic cylinder. Possibility to apply line widths ranging from 10 - 20 cm depending on line thickness, work conditions, application speed and layer thickness. As an alternative, we offer a narrow nozzle, which can spray 5-15 cm with one gun. Optional narrow nozzle size of 3 mm or wide nozzle size of 7 mm.The guns are mounted on a sliding retainer frame, on which 1-3 spray guns and 1-3 bead guns are attached. Easily slidable from side to side for an optimal working position. Ground distance is maintained by retainer wheels to ensure a constant road marking width. All material pipes are oil-jacketed and insulated to maintain an ideal material temperature. Lifting of retainer from operators seat using a hydraulic cylinder.

Thermoplastic Spray Advantages

Due to the equipment working via a pressure vessel, it is very simple and easy to use as the pressure in the vessel is the same as the pressure in the application. Furthermore, the tank requires very little maintenance.Thermoplastic spray markings are a cost-efficient solution as the applied lines do not require as much material as extruded profiled markings. Furthermore, this type of material forms a uniform application that is more durable and dries faster compared to cold paint applications.

3-in-1 solution for thermoplastic markings

The Dot’n line system offers a three-in-one solution for thermoplastic markings. This equipment can apply flat lines, dots and unique combination of lines and dots using only one extruder head.In the drawing you can see examples of different valve set-ups giving different widths. The total line width can be between 30-50 cm depending on the set-up. The line width starts at 5 cm and can be built up to 50 cm with 5 cm standard shutters.

Dot specifications

By using two sets of shutters the base line has time to cure slightly before the Dots are applied. Consequently, the Dots will settle on top of the line with sharp edges, securing the optimum retroreflection.The diameter of dots can be chosen between ø18 and ø 45 mm depending on the chosen drum. The number of dots/meter is 15-35 dots and is controlled by the LineMaster.The shutters have no contact with the high tensile steel drum and therefore wear is minimalized and lifetime is prolonged.Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven.Pneumatically controlled quick cleaning systemfor removal of solids left in the extrusion slot.It can be activated while extrusion is in processand is only slightly detectable on the line in theform of a moderate thickening of the layer.Continuous circulation of the thermoplastic material inside the equipment. This avoids settling and catching of solid parts and prevents unnecessary wear of mechanical parts.The application speed depends on the type of application and goes up to 6 km/h.

AUGER SCREW PUMP WITH CONTINUOUS RECIRCULATION SYSTEM

The transport of material from tank to Dot'n'Line head is done by a hydraulically driven auger screw pump, which is electronically controlled. The screw pump has a permanent thermoplastic re-circulation system, which ensures a constant flow also past the inactive extrusion shutters, keeping solid parts from settling and keeping the equipment ready for working.Build-in pressure regulating system ensures that line width and thickness do not change no matter the number of shutters involved in the current marking assignment.

Advantages of profiled dot markings

Having numerous dots in a line gives the light a lot of possible areas to fall onto and create a retro-reflective effect. This is essential for having clear visibility, especially while driving during night time.The drainage effect of the profiled markings ensures that rain water will easily drain away from the lines, thus maintaining high reflective values in rainy weather. This is possible because of the structure that allows the water to drain. Furthermore, the profiled nature of the road marking produces a noise when driven over that will warn the driver against driving off the road.

LineMaster features

The Borum LineMaster control unit is an easy way of setting and controlling your line marking jobs. The LineMaster is attached to the operator's section of the machine and gives you full control of all your line marking tasks, from line application and pre-marking to reporting and invoicing. It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types and different combinations to have them ready for marking, and can instantly adjust them on the go.Furthermore, you are able to view the status of various parts of the machine (e.g. compressor) on the computer screen that will help with correctly maintaining the machine and avoiding break downs.

QUICK CLEANING

Pneumatically controlled quick cleaning system for removal of solids left in the extrusion slot. It can be activated while extrusion is in process and is only slightly detectable on the line in the form of a moderate thickening of layer.

Mounting the RibLine equipment

Speed and width of application

Fixed pointer

With hydraulic lifting system

Sunshade with 1 rotating light

Remote control for BM LineMaster

Bead alarm mounted on bead gun

Air drier for bead tank

Ejector filling of bead tank

Hydraulic broom

Airknife

Cone holder

Bar with pneumatic lift for mounting warning lights

(Comes without lights)

Pre-marking system with paint can

Pre-marking system with paint gun

BM Online

Quick shift