2 COMPONENT EXTRUSION AND AGGLOMERATE APPLICATION (98:2)
From city areas to urban and interurban roads, the Borum® Master 2000 can handle both smaller jobs and longer road stretches.
The BM 2000 CP T AG is an agile machine with excellent load abilities and a turning radius of only 3.2 m. It allows for paint tank capacities of 440 L or 2 x 220 L.
The BM 2000 has a one-seat slidable drive and operator section for flexible working on the left or right side.
The 2-component application equipment can be set to execute lines in widths between 10-30 cm. The equipment on this machine may be used for the application of flat lines, profiled dots, and agglomerate markings .
Line types that can be applied with this equipment
Pressurized material tank and filters in stainless steel for water and ammonium based paints.
The material tank has a filling system with two filling holes. This makes the filling process very easy to manage.
Driven by hydraulic motor and with
manually operated reversing valve.
The Borum Vario Retainer provides a unique possibility to interchange between applications in a very short time, with very few standard tools. When the work is done, the retainer and application equipment can be easily stowed under the machine.
The retainer makes it possible to use all application equipment in different positions on the machine.
Easily slidable from side to side for an optimal working position. Ground distance is maintained by retainer wheel to ensure a constant road marking width.
The pump system consists of a lobe type paint pump and gear type pump for hardener. The two pumps are driven by one hydraulic motor via chain and variable gearbox securing the 98:2 relation between paint and hardener.
The system is also equipped with a controller for performing the flushing of gun(s) and mixer.
The extruder is ordered for the specific line width. The line width can be 10-30 cm and the line thickness can set to 1-3 mm (ribs/profiles can be up to 10mm depending on the material).
The extruder head is provided with a quick connector to the mixer head for easy exchange of equipment. The extruder is also provided with a pneumatic cylinder with cleaning arrangement.
The extruder is ordered for the specific line width. Available line widths are 10, 12, 15, 17, 20, 22, 24, 25, 30 (4, 5, 6, 7, 8, 8.5, 9, 9.5, 10, 12 inch.) Provided with quick connector to the mixer head for easy exchange of head.
Usual marking speed is between 2-6 km/h depending on work and weather conditions, operator experience, etc. Faster application speeds can be achieved.
Recommended paint viscosity for extruded lines is higher than 6500 cp and for ribs is higher than 8500 cp.
Fitting and exchanging the Borum 2-Component Extruder with other 2-component equipment, such as Dot or Agglomerate, can be done in less than 2 minutes, without the use of tools.
Must be mounted under extruder unit. Line size depends on the extruder.
The line width can be up to 30 cm, the line thickness can be up to 4 mm, and the line type is stochastic structure. The equipment can apply marking at a speed of up to 5 km/h.
The Borum® 2-Component Agglomerate is a very flexible one-size unit, made for fitting under any Borum 2-Component Extruder.
The Borum 2K Agglomerate is made to be flexible and easy to use. Once the brackets are placed on the extruder, any mounting and unmounting can be done in less than 5 minutes without using tools at all. Adjusting the equipment to make the exact marking needed is very simple, and once it is done, mounting and unmounting is Click-on/Click-off.
Agglomerate marking on the road is controlled from the Borum LineMaster. Cleaning is done automatic. No need for mechanically adjusting the valves. Just raise the retainer, place the special container for cleaning and push the button on the LineMaster computer. If the spikes on the agglomerate roller need to be thoroughly cleaned, it is easily done by shifting two levers. This allows the spike roller to be put into a bucket with solvent. Overall, the cleaning process does not require any tools to be completed.
The cleaning system is formed by a solvent tank for cleaning of mixer-head, hoses and paint guns. The system is activated via the Borum LineMaster computer. The cleaning process is an automated preset sequence ensuring the correct valves are opening/closing.
36L (79 lb wt.) pressure solvent tank for cleaning of mixer-head, hoses and paint guns.
Stainless steel, max 8.5 bar (123 psi).
NB! When working with 2-component whenever the application is stopped, application equipment has to be cleaned from the cold plastic mixture within a few minutes.
The Borum LineMaster control unit is an easy way of setting and controlling your line marking jobs. The LineMaster is attached to the operator's section of the machine and gives you full control of all your line marking tasks, from line application and pre-marking to reporting and invoicing.
It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types, colours and combinations to have them ready for marking, and can instantly adjust them on the go.
Furthermore, you are able to view the status of various mechanical parts of the machine (e.g. compressor) on the computer screen that will help with correctly maintaining the machine and avoiding break downs.