DOT'N LINE THERMOPLASTIC EXTRUSION
From city areas to urban and interurban roads, the Borum Master 1500 can handle both smaller jobs and longer road stretches.
The BM 1500 DL is an agile machine with excellent load abilities and a turning radius of only 3.2 m. It allows for material tank capacity of 265 L.
Equipped with the new generation of Borum’s LineMaster computer, operating the machine is easy and convenient. Important controls are now integrated in the armrest.
The thermoplastic Borum extruder can apply lines of 5 – 30 cm width depending on the configuration of the equipment. The equipment is capable of applying flat lines, profiled lines, dots and a combination of dots and lines.
See more detailed descriptions further on.
Line types that can be applied with this equipment
Non-pressurized thermoplastic tank, indirectly heated via heat transfer oil. The thermal oil and thermoplastic material temperature is thermostatically controlled and regulated automatically according to the settings
Diesel burner system for heating of the thermal oil (and thermoplastic). Propane burner available on demand.
Vertical agitator (mixer)
With hydraulic transmission. Heated center pipe for efficient uniform temperature control. Perfect melting & homogenization of the thermoplastic. Stable construction with foundation and bearings at the top of the material tank.
The Dot’n line system offers a three-in-one solution for thermoplastic markings. This equipment can apply flat lines, dots and unique combination of lines and dots using only one extruder head.
In the drawing drawing you can see examples of different valve set-ups giving different widths. The equipment's width can be up to 30 cm. The line width starts at 5 cm and can be built up to 30 cm with 5 cm standard valves.
By using two sets of shutters the base line has time to cure slightly before the Dots are applied. Consequently, the Dots will settle on top of the line with sharp edges, securing the optimum retroreflection.
The diameter of dots can be chosen between ø18 and ø 45 mm depending on the chosen drum. The number of dots/meter is 15-35 dots and is controlled by the LineMaster.
The shutters have no contact with the high tensile steel drum and therefore wear is minimalized and lifetime is prolonged.
Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven.
Continuous circulation of the thermoplastic material inside the equipment. This avoids settling and catching of solid parts and prevents unnecessary wear of mechanical parts.
The application speed depends on the type of application and goes up to 6 km/h.
The transport of material from tank to Dot'n'Line head is done by a hydraulically driven auger screw pump, which is electronically controlled. The screw pump has a permanent thermoplastic re-circulation system, which ensures a constant flow also past the in-active extrusion shutters, keeping solid parts from settling and keeping the equipment ready for working
Build-in pressure regulating system ensures that line width and thickness do not change no matter the number of shutters involved in the current marking assignment.
Having numerous dots gives the light a lot of possible areas to fall onto and create a retro-reflective effect. This is essential for having clear visibility, especially while driving during night time.
The drainage effect of the profiled markings ensures that rain water will easily drain away from the lines, thus maintaining high reflective values in rainy weather. This is possible because of the structure that allows the water to drain. Furthermore, the profiled nature of the road marking produces a noise when driven over that will warn the driver against driving off the road.
The Borum LineMaster control unit is an easy way of setting and controlling your line marking jobs. The LineMaster is attached to the operator's section of the machine and gives you full control of all your line marking tasks, from line application and pre-marking to reporting and invoicing.
It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types, colours and combinations to have them ready for marking, and can instantly adjust them on the go.
Furthermore, you are able to view the status of various parts of the machine (e.g. compressor) on the computer screen that will help with correctly maintaining the machine and avoiding break downs.