The Borum® Master 3000 series provides you with a variety of high capacity line marking machines designed for large scale jobs such as marking highways, motorways or airport runways.

The material tank capacity can be up to 450L. The possibility for the large material capacity naturally gives fewer stops during the day for refilling.

The BM 3000 has a two-seat slidable drive and operator section for flexible working on left or right side.

Depending on the equipment, the machine can apply both flat and profiled markings, single and double lines of different widths, as well as for simultaneous application of continuous and interrupted lines.

Line Types

Line types that can be applied with this equipment

Contact us about this product

ENGINE

  • Manufacturer : Kubota
  • Type : Turbo
  • Cooling : Water
  • Cylinder : 4 stroke 3600 cm3
  • RatedPower : 63 KW
  • Approval : EU Stage IIIA resp. TIER 3

COMPRESSOR

  • Compressor Capacity : Choice of 1-2 compressors can give 1800 - 3600 L/min @ 10 bar. Integrated oil-cooling system. Air-cooler incl. water separator

FILLING CAPACITIES

  • Fuel tank capacity : 180 L (2 x 90 L)
  • Hydraulic tank size : 93 L
  • Bead capacity : 330 L (2 x 165 L). Pressurised (max 3 bars)

MATERIAL TANK

  • Material Tank : 445 L

DRIVING PROPERTIES

  • Drive angle : 10.4 degrees / 18% (5000 kg)
  • Turning radius : 4.90 m.
  • Steering : Dual torque steering

TRANSMISSION

  • Hydrostatic transmission : For variable speed
  • Speed : 0-22 km/h

ELECTRICAL SYSTEM

  • Electrical system : 12 V / 130 Amp

CONTROL UNIT

  • Borum LineMaster : Program up to 99 different line types. Organise lines in up to 30 marking programs. 8" display. Transfer of daily marking reports. See more detailed info.

COLOUR

  • Colour : RAL 1007 (Other colours available on request)

DIMENSIONS

  • Length : 5350 mm
  • Width : 1300 mm
  • Height : 2250 mm

THERMOPLASTIC NON-PRESSURIZED TANK:

Non-pressurized thermoplastic tank indirectly heated via heat transfer oil. The thermal oil and thermoplastic material temperature is thermostatically controlled and regulated automatically.

Vertical agitator (mixer)
With hydraulic transmission. Heated center pipe for efficient uniform temperature control. Perfect melting & homogenization of the thermoplastic. Stable construction with foundation and bearings at the top of the material tank.

Burner system
Diesel burner system for heating of the thermal oil (and thermoplastic). Propane burner available on demand.

THERMOPLASTIC RIBLINE APPLICATION

The Borum thermoplastic RibLine application equipment can be set to execute lines in widths up to 30 cm.
The RibLine application equipment can apply both flat lines and a combination of lines and ribs.

Mounting the RibLine equipment

The RibLine equipment is mounted directly on the side of the material tank. Alternatively, if the machine is also equipped with a thermoplastic extruder, you can mount it on the side of the extruder.
The equipment is supplied by an automatic filling system with a pneumatic level center.

3-in-1 solution for thermoplastic markings

The Dot’n line system offers a three-in-one solution for thermoplastic markings. This equipment can apply flat lines, dots and unique combination of lines and dots using only one extruder head.

In the drawing you can see examples of different valve set-ups giving different widths. The equipment's width can be between 30-50 cm. The line width starts at 5 cm and can be built up to 50 cm with 5 cm standard valves.

Dot specifications

By using two sets of shutters the base line time to cure slightly before the Dots are applied and consequently the Dots will settle on top of the line with sharp edges, securing the optimum retroreflection.

Diameter of dots can be chosen between ø18 and ø 45 mm depending on the chosen drum. Number of dots/meter is 15-35 dots and is controlled by the LineMaster.

The shutters do not touch the high tensile steel drum and therefore the lifetime is prolonged.

Effective heating of the complete unit using a centrifugal pump, 42 L/min, hydraulically driven.

Continuous circulation of the thermoplastic material inside the equipment. This avoids settling and catching of solid parts and prevents unnecessary wear of mechanical parts.

The application speed depends on the type of application and goes up to 6 km/h.

SCREW PUMP WITH CONTINUOUS RECIRCULATION SYSTEM

The transport of material from tank to Dot'n'Line head is done by a hydraulically driven screw pump, which is electronically controlled. The screw pump has a permanent thermoplastic re-circulation system, which ensures a constant flow also past the in-active extrusion valves, keeping solid parts from adhering and ready for opening.

Build-in pressure regulating system ensures that line width and thickness do not change no matter the number of the shutters involved in the current marking assignment.

Advantages of profiled dot markings

Having numerous dots gives the light a lot of possible areas to fall onto and create a retro-reflective effect. This is essential for having clear visibility, especially while driving during night time.

The drainage effect of the profiled markings ensures that rain water will easily drain away from the lines, thus maintaining high reflective values in rainy weather. This is possible because of the structure that allows the water to drain. Furthermore, the profiled nature of the road marking produces a noise when driven over that will warn the driver against driving off the road.

THERMO SPRAY APPLICATION (PUMP)

The thermoplastic spray application equipment works via a pump. The amount of the applied material is set by the pressure of the pump and the air pressure of spraying, but the pump can also be adjusted to the speed of the machine.

SPRAY-PLASTIC PUMP

Spray-plastic pump operates with a non-pressurised material tank. The pump consists of a hydraulically driven motor, gearbox, clutch, highly durable rotors and pump house. Pump housing is oil-jacketed and isolated. Capacity up to 80 L/min. at 8.5 bar (21 gal/min. at 123 psi).

The hydraulic control valve adjusts the quantity of spray-plastic material according to the speed of the machine in order to obtain a constant layer thickness.

The application speed can go up to 15 km/h.

BM SP 2500 SPRAY-PLASTIC GUN

Automatic high-capacity spray plastic gun. Consists of an oil jacketed gun body and a pneumatic cylinder. Possibility to apply line widths ranging from 10 - 20 cm depending on line thickness, work conditions, application speed and layer thickness. As an alternative, we offer a narrow nozzle, which can spray 5-15 cm with one gun.

Optional narrow nozzle size of 3 mm or wide nozzle size of 7 mm.

Sliding retainer

Hydraulic transmission with motor, shaft, safety valve and on/off valve.

Sliding retainer frame, on which 1-3 spray guns and 1-3 bead guns are attached. Easily slideable from side to side for an optimal working position.
Ground distance is maintained by retainer wheels to ensure a constant road marking width. All material pipes are oil-jacketed and insulated to maintain an ideal material temperature.
Lifting of retainer from operators seat using a hydraulic cylinder.

Automatic high-capacity spray plastic gun. Consists of an oil jacketed gun body and a pneumatic cylinder.

Advantages of using a pump equipment

The spray plastic application equipment that works with a pump gives you the possibility of quickly adjusting the pressure while driving. Our LineMaster may also to a certain extent do this automatically.

Furthermore, filling and thermoplastic filtration is easy, since the tank lid is larger than the one on the pressurized tank.

Sprayed thermoplastic forms a uniform application that is more durable and dries faster compared to cold paint applications.

LineMaster features

The Borum LineMaster allows you efficient control of all line marking tasks, from line application and pre-marking to reporting and invoicing. It is possible to store up to 99 different line types, and to arrange these in up to 30 different marking programs. You are also able to pre-set line widths, line types, colours and combinations to have them ready for marking, and can instantly adjust them on the go.

CRUISE CONTROL

For your convienience we recommend use of cruise control. Read more about the cruise control in the Borum Knowledge Lab on www.borum.as.

QUICK CLEANING

Pneumatically controlled quick cleaning system for removal of solids left in the extrusion slot. Can be activated while extrusion is in process and is only slightly detectable on the line in the form of a moderate thickening of layer.

Ejector filling of bead tank

Pointer turning with steering

With hydraulic lifting system

Fixed pointer

With hydraulic lifting system

Cruise control

Sunshade with 1 rotating light

Bead alarm mounted on bead gun

Remote control for BM LineMaster

Cone holder

Bar with pneumatic lift for mounting warning lights

(Comes without lights)

Air drier for bead tank

GPS system

Pre-marking system with paint gun

Airknife

Pre-marking system with paint can

Hydraulic broom

Quick shift

BORuM ON SOCIAL MEDIA

Follow us on these social platforms